case_id,batch_a,batch_b,m,n,k,dtype_a,dtype_b,dtype_c,trans_a,trans_b,has_bias,out_nd,deterministic_level,plan_case_id,plan_branch,plan_npu,plan_op,plan_used_core_num,plan_split_b,plan_m_cnt,plan_n_cnt,plan_grid_k,plan_core_map,plan_b_core,plan_merge_b0,plan_single_core_m,plan_single_core_n,plan_single_core_k,plan_k_l1,plan_b_l1,plan_l1_form,plan_base_m,plan_base_n,plan_base_k,plan_l2_policy_in,plan_l2_policy_out,plan_swizzle_w,plan_workspace_bytes,plan_tail_strategy,plan_tail_m_cnt,plan_tail_n_cnt,plan_tail_k_cnt,plan_tail_m_main,plan_tail_n_main,plan_tail_block_cnt,plan_tail_wave_num,plan_fixpipe_unitflag,plan_out_dtype_bytes,plan_note,gm_read_bytes,l2_read_bytes,t_mte2_gm,t_mte2_l2,t_mte2,dma_cmd_count,t_dma_cmd,cube_flops,t_mmad,fixpipe_bytes,t_fixpipe,t_reduce,t_steady,t_drain,t_total,bottleneck,feasible,violations,bound_type,advice
to_matmul_demo,1,1,2048,2048,2048,bf16,bf16,bf16,False,False,False,True,0,to_matmul_demo,转Matmul,Ascend950PR,batch_mat_mul_v3,32,1,0,0,1,"折叠为 Matmul [2048,2048]x[2048,2048], 复用 Matmul 切分体系",0,1,0,0,2048,0,1,,0,0,0,,,0,0,转Matmul后由 Matmul 体系决定,1,1,1,0,0,0,0,True,2,"BatchB=1免费折叠: 左矩阵 [1,2048,2048] 视图折叠为 [2048,2048], 零重排零 split",16777216,0.0,1.048576e-05,0.0,1.048576e-05,0.0,0.0,17179869184.0,3.534952506995885e-05,8388608,1.6131938461538462e-06,0.0,3.534952506995885e-05,0.0,3.534952506995885e-05,MMAD,True,,计算Bound,"瓶颈在 Cube 计算: 已接近理论算力上限, 检查是否有冗余计算 (MergeBatch 交叉项) 可消除"
special_k0_demo,128,128,256,256,0,bf16,bf16,bf16,False,False,False,True,0,special_k0_demo,特殊分支,Ascend950PR,batch_mat_mul_v3,64,1,1,1,1,AIV 核间按行均分 (无 Cube tile 概念),0,1,0,0,0,0,1,UB驻留(AIV),0,0,0,allocate,direct_gm,0,0,不涉及(AIV逐元素),1,1,1,0,0,0,0,False,2,"K=0纯写值: 无任何计算, C=bias 或 0, 纯 AIV 写值; 按行均分到 AIV 核",0.0,0.0,0.0,0.0,0.0,0.0,0.0,0.0,0.0,16777216,3.2263876923076923e-06,0.0,3.2263876923076923e-06,0.0,3.2263876923076923e-06,FIXPIPE,True,,写出Bound(L2写口),"瓶颈在 Fixpipe 写出: 检查输出 dtype (fp16/fp8 可减半写出量), 或评估输出驻留 L2 异步回写策略"
special_k1_demo,128,128,256,256,1,bf16,bf16,bf16,False,False,False,True,0,special_k1_demo,特殊分支,Ascend950PR,batch_mat_mul_v3,64,1,1,1,1,AIV 核间按行均分 (无 Cube tile 概念),0,1,0,0,1,0,1,UB驻留(AIV) UB乒乓,0,0,0,allocate,direct_gm,0,0,不涉及(AIV逐元素),1,1,1,0,0,0,0,False,2,"K=1逐元素乘: 退化为 C=A⊙B 无累加深度, Cube 16x16x16 粒度浪费 15/16; 走 AIV 通路 GM->UB->Mul->GM, UB乒乓 (B>=2*AIV 双batch乒乓流水)",131072,0.0,8.192e-08,0.0,8.192e-08,0.0,0.0,8388608.0,3.103030303030303e-07,16777216,3.2263876923076923e-06,0.0,3.2263876923076923e-06,0.0,3.2263876923076923e-06,FIXPIPE,True,,写出Bound(L2写口),"瓶颈在 Fixpipe 写出: 检查输出 dtype (fp16/fp8 可减半写出量), 或评估输出驻留 L2 异步回写策略"
merge_demo_k_trunc,2048,2048,32,32,256,bf16,bf16,bf16,False,False,False,True,0,merge_demo_k_trunc,MergeBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B均分(核间零重复读零依赖),64,4,128,128,256,256,8,合并驻留,128,128,128,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,"b0=4 (L0C上限5.7/算存比上限19.0/b_core=64); K截断; 合并后单次DMA搬入 A'[128,256]+B'[256,128]; 输出落点: L2驻留 (整case V_in+V_out=64.0MB vs L2=128MB)",67108864,0.0,4.194304e-05,0.0,4.2743039999999997e-05,16.0,8.000000000000001e-07,4294967296.0,8.837381267489712e-06,4194304,8.065969230769231e-07,0.0,4.2743039999999997e-05,1.8849638999683443e-07,4.293153638999683e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
merge_iter_arbitrate,128,128,64,64,512,bf16,bf16,bf16,False,False,False,True,0,merge_iter_arbitrate,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),4,1,64,64,512,512,2,b_双batch乒乓,64,64,256,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,双batch乒乓: 2*(MK+KN)*dtype=256KB <= L1; 输出落点: L2驻留,16777216,0.0,1.048576e-05,0.0,1.0685759999999999e-05,4,2.0000000000000002e-07,536870912.0,1.104672658436214e-06,1048576,2.0164923076923077e-07,0.0,1.0685759999999999e-05,3.265804723013612e-07,1.101234047230136e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
iter_demo_form_b,128,128,64,64,256,bf16,bf16,bf16,False,False,False,True,0,iter_demo_form_b,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),4,1,64,64,256,256,2,b_双batch乒乓,64,64,256,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,双batch乒乓: 2*(MK+KN)*dtype=128KB <= L1; 输出落点: L2驻留,8388608,0.0,5.24288e-06,0.0,5.4428799999999995e-06,4,2.0000000000000002e-07,268435456.0,5.52336329218107e-07,1048576,2.0164923076923077e-07,0.0,5.4428799999999995e-06,1.8849638999683443e-07,5.631376389996834e-06,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
iter_demo_form_d,64,64,64,64,8192,bf16,bf16,bf16,False,False,False,True,0,iter_demo_form_d,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),2,1,64,64,8192,1024,1,d_两侧都切K,64,64,256,allocate(GM->L1随路驻留L2),"direct_gm(整case超L2: 输入优先驻留L2, 输出直写GM不占L2)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,"两侧都切K: k_L1=1024, K段成对流水, batch边界天然无缝; dValueA=2048B/dValueB=128B; 输出落点: 直写GM",134217728,0.0,8.388608e-05,0.0,8.468608e-05,16,8.000000000000001e-07,4294967296.0,8.837381267489712e-06,524288,3.2768e-07,0.0,8.501376e-05,7.16176329218107e-07,8.572993632921812e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
streamk_demo,4,4,128,128,10240,bf16,bf16,bf16,False,False,False,True,0,streamk_demo,StreamK,Ascend950PR,batch_mat_mul_v3,32,1,1,1,32,"B/M/N切出4块, 每块32核切K归约 (归约组内核c负责K段[c*K/32,(c+1)*K/32))",1,1,128,128,320,256,1,K段标准分块流水,128,128,64,allocate(部分和驻留L2),"resident(部分和4B驻留L2, 防精度丢失不随C的fp16/fp8转换)",0,8388608,grid_K=32路切K+归约,1,1,32,0,0,0,0,True,4,"P=1.00, grid_K=32, 部分和驻留L2按4B写出, AIV归约后按C dtype=2B写最终",20971520,0,1.31072e-05,0.0,1.31072e-05,0.0,0.0,1342177280.0,2.761681646090535e-06,0.0,0.0,3.4067453613053613e-06,1.31072e-05,3.4067453613053613e-06,1.651394536130536e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
asw_demo_full,2,2,8192,8192,1024,bf16,bf16,bf16,False,False,False,True,0,asw_demo_full,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,47,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,1024,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,方案B,52,52,1,52,52,2,139,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=64.0MB, V_out=256.0MB, L2=128MB); 尾轮: 周长型主导, rho=0.06<rho_dv=0.53, A1b被dValue卡死, 方案B反超",67108864,3087007744,4.194304e-05,0.0005936553353846154,0.0006355983753846153,0.0,0.0,274877906944.0,0.0005655924011193416,268435456,0.00016777216,0.0,0.0008033705353846154,0.0,0.0008033705353846154,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
asw_demo_reduce_core,16,16,256,256,128,bf16,bf16,bf16,False,False,False,True,0,asw_demo_reduce_core,ASW_Basic_降核,Ascend950PR,batch_mat_mul_v3,16,1,1,1,1,"降核: 只用16核, 每核一个L0C满载输出块, 其余核闲置",0,1,256,256,128,128,1,标准核内流水,256,256,64,allocate,resident(整case全驻留S_A),0,0,不涉及(每核一块无尾轮),1,1,1,0,0,0,0,True,2,"P=16.00<C, 降核是理性选择 (强切则 tile 跌破搬移效率下限反而更慢)",2097152,0,2.62144e-06,0.0,2.62144e-06,0.0,0.0,268435456.0,1.104672658436214e-06,2097152,8.065969230769231e-07,0.0,2.62144e-06,0.0,2.62144e-06,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b4_m1_n128_k256,4,4,1,128,256,bf16,bf16,bf16,False,False,False,True,0,b4_m1_n128_k256,ASW_Basic_降核,Ascend950PR,batch_mat_mul_v3,1,1,1,1,1,"降核: 只用1核, 每核一个L0C满载输出块, 其余核闲置",0,1,1,128,256,256,1,标准核内流水,1,128,128,allocate,resident(整case全驻留S_A),0,0,不涉及(每核一块无尾轮),1,1,1,0,0,0,0,True,2,"P=0.01<C, 降核是理性选择 (强切则 tile 跌破搬移效率下限反而更慢)",264192,0,5.28384e-06,0.0,5.28384e-06,0.0,0.0,262144.0,1.7260510288065844e-08,1024,6.3015384615384615e-09,0.0,5.28384e-06,0.0,5.28384e-06,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b8_m2_n192_k128,8,8,2,192,128,bf16,bf16,bf16,False,False,False,True,0,b8_m2_n192_k128,ASW_Basic_降核,Ascend950PR,batch_mat_mul_v3,1,1,1,1,1,"降核: 只用1核, 每核一个L0C满载输出块, 其余核闲置",0,1,2,192,128,128,1,标准核内流水,2,192,80,allocate,resident(整case全驻留S_A),0,0,不涉及(每核一块无尾轮),1,1,1,0,0,0,0,True,2,"P=0.05<C, 降核是理性选择 (强切则 tile 跌破搬移效率下限反而更慢)",397312,0,7.94624e-06,0.0,7.94624e-06,0.0,0.0,786432.0,5.178153086419753e-08,6144,3.7809230769230766e-08,0.0,7.94624e-06,0.0,7.94624e-06,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b16_m4_n256_k192,16,16,4,256,192,bf16,bf16,bf16,False,False,False,True,0,b16_m4_n256_k192,ASW_Basic_降核,Ascend950PR,batch_mat_mul_v3,1,1,1,1,1,"降核: 只用1核, 每核一个L0C满载输出块, 其余核闲置",0,1,4,256,192,192,1,标准核内流水,4,256,64,allocate,resident(整case全驻留S_A),0,0,不涉及(每核一块无尾轮),1,1,1,0,0,0,0,True,2,"P=0.25<C, 降核是理性选择 (强切则 tile 跌破搬移效率下限反而更慢)",1597440,0,3.19488e-05,0.0,3.19488e-05,0.0,0.0,6291456.0,4.1425224691358024e-07,32768,2.0164923076923077e-07,0.0,3.19488e-05,0.0,3.19488e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m8_n128_k256,32,32,8,128,256,bf16,bf16,bf16,False,False,False,True,0,b32_m8_n128_k256,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),1,1,8,128,256,256,1,a_单batch全驻留,8,128,128,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,单batch全驻留: (MK+KN)*dtype=68KB <= L1; 输出落点: L2驻留,2228224,0.0,1.39264e-06,0.0,1.44264e-06,1,5.0000000000000004e-08,16777216.0,3.452102057613169e-08,65536,1.2603076923076923e-08,0.0,1.44264e-06,4.712409749920861e-08,1.4897640974992086e-06,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b64_m16_n256_k512,64,64,16,256,512,bf16,bf16,bf16,False,False,False,True,0,b64_m16_n256_k512,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),2,1,16,256,512,240,1,c_一侧驻留+对侧切K,16,256,64,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,"一侧驻留(A)+对侧切K: A驻留16KB, 预算L1/2, k_L1=240, dValueA=480B/dValueB=512B; 输出落点: L2驻留",17825792,0.0,1.114112e-05,0.0,1.1441120000000001e-05,6,3.0000000000000004e-07,268435456.0,5.52336329218107e-07,524288,1.0082461538461538e-07,0.0,1.1441120000000001e-05,1.798661348528015e-07,1.1620986134852803e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b128_m8_n192_k256,128,128,8,192,256,bf16,bf16,bf16,False,False,False,True,0,b128_m8_n192_k256,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),4,1,8,192,256,256,2,b_双batch乒乓,8,192,80,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,双batch乒乓: 2*(MK+KN)*dtype=200KB <= L1; 输出落点: L2驻留,13107200,0.0,8.192e-06,0.0,8.392e-06,4,2.0000000000000002e-07,100663296.0,2.0712612345679012e-07,393216,7.561846153846153e-08,0.0,8.392e-06,7.068614624881291e-08,8.462686146248813e-06,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m16_n8192_k7168,32,32,16,8192,7168,bf16,bf16,bf16,False,False,False,True,0,b32_m16_n8192_k7168,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,1,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,7168,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,47,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=3591.0MB, V_out=8.0MB, L2=128MB); 尾轮: r=0 无尾轮",3765436416,337641472,0.00235339776,6.493105230769231e-05,0.0024183288123076924,0.0,0.0,60129542144.0,0.00012372333774485596,8388608,5.24288e-06,0.0,0.0024235716923076923,0.0,0.0024235716923076923,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b4_m1_n8192_k8192,4,4,1,8192,8192,bf16,bf16,bf16,False,False,False,True,0,b4_m1_n8192_k8192,StreamK,Ascend950PR,batch_mat_mul_v3,32,1,1,1,32,"B/M/N切出4块, 每块32核切K归约 (归约组内核c负责K段[c*K/32,(c+1)*K/32))",1,1,1,8192,256,256,1,K段标准分块流水,1,128,64,allocate(部分和驻留L2),"resident(部分和4B驻留L2, 防精度丢失不随C的fp16/fp8转换)",0,4194304,grid_K=32路切K+归约,1,1,32,0,0,0,0,True,4,"P=0.50, grid_K=32, 部分和驻留L2按4B写出, AIV归约后按C dtype=2B写最终",536936448,0.0,0.00033558528,0.0,0.00033558528,0.0,0.0,536870912.0,1.104672658436214e-06,0.0,0.0,1.731729603729604e-06,0.00033558528,1.731729603729604e-06,0.0003373170096037296,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b16_m2_n4096_k7168,16,16,2,4096,7168,bf16,bf16,bf16,False,False,False,True,0,b16_m2_n4096_k7168,StreamK,Ascend950PR,batch_mat_mul_v3,32,1,1,1,16,"B/M/N切出16块, 每块16核切K归约 (归约组内核c负责K段[c*K/16,(c+1)*K/16))",1,1,2,4096,448,256,1,K段标准分块流水,2,128,64,allocate(部分和驻留L2),"resident(部分和4B驻留L2, 防精度丢失不随C的fp16/fp8转换)",0,8388608,grid_K=16路切K+归约,1,1,16,0,0,0,0,True,4,"P=2.00, grid_K=16, 部分和驻留L2按4B写出, AIV归约后按C dtype=2B写最终",939982848,0,0.00058748928,0.0,0.00058748928,0.0,0.0,1879048192.0,3.866354304526749e-06,0.0,0.0,1.7726896037296038e-06,0.00058748928,1.7726896037296038e-06,0.0005892619696037297,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m64_n64_k7168,32,32,64,64,7168,bf16,bf16,bf16,False,False,False,True,0,b32_m64_n64_k7168,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),1,1,64,64,7168,1024,1,d_两侧都切K,64,64,256,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,"两侧都切K: k_L1=1024, K段成对流水, batch边界天然无缝; dValueA=2048B/dValueB=128B; 输出落点: L2驻留",58720256,0.0,3.670016e-05,0.0,3.7050160000000004e-05,7,3.5000000000000004e-07,1879048192.0,3.866354304526749e-06,262144,5.041230769230769e-08,0.0,3.7050160000000004e-05,6.027486369104147e-07,3.765290863691042e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b64_m1024_n1024_k7168,64,64,1024,1024,7168,bf16,bf16,bf16,False,False,False,True,0,b64_m1024_n1024_k7168,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),2,1,1024,1024,7168,64,1,d_两侧都切K,176,176,64,allocate(GM->L1随路驻留L2),"direct_gm(整case超L2: 输入优先驻留L2, 输出直写GM不占L2)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,"两侧都切K: k_L1=64, K段成对流水, batch边界天然无缝; dValueA=128B/dValueB=2048B; 输出落点: 直写GM",1879048192,0.0,0.00117440512,0.0,0.0011856051200000001,224,1.1200000000000001e-05,962072674304.0,0.0019795734039176954,134217728,8.388608e-05,0.0,0.0019795734039176954,5.078042126748971e-05,0.0020303538251851853,MMAD,True,,计算Bound,"瓶颈在 Cube 计算: 已接近理论算力上限, 检查是否有冗余计算 (MergeBatch 交叉项) 可消除"
b128_m2048_n2048_k1536,128,128,2048,2048,1536,bf16,bf16,bf16,False,False,False,True,0,b128_m2048_n2048_k1536,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,12,12,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,1536,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,576,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=1536.0MB, V_out=1024.0MB, L2=128MB); 尾轮: r=0 无尾轮",1610612736,17716740096,0.00100663296,0.003407065403076923,0.004413698363076923,0.0,0.0,1649267441664.0,0.0033935544067160493,1073741824,0.00067108864,0.0,0.005084787003076923,0.0,0.005084787003076923,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b64_m1024_n8192_k2048,64,64,1024,8192,2048,bf16,bf16,bf16,False,False,False,True,0,b64_m1024_n8192_k2048,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,6,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,2048,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,564,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=2304.0MB, V_out=1024.0MB, L2=128MB); 尾轮: r=0 无尾轮",2415919104,23085449216,0.00150994944,0.004439509464615385,0.005949458904615385,0.0,0.0,2199023255552.0,0.004524739208954733,1073741824,0.00067108864,0.0,0.006620547544615385,0.0,0.006620547544615385,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m1024_n1024_k512,32,32,1024,1024,512,bf16,bf16,bf16,False,False,False,True,0,b32_m1024_n1024_k512,IterBatch,Ascend950PR,batch_mat_mul_v3,32,32,1,1,1,切B轮转分配(核间零重复读零依赖),1,1,1024,1024,512,64,1,d_两侧都切K,176,176,64,allocate(GM->L1随路驻留L2),"resident(整case输入+输出<=L2: 输出驻留L2异步回写, GM写=0)",0,0,不涉及(核内不切M/N),1,1,1,0,0,0,0,True,2,"两侧都切K: k_L1=64, K段成对流水, batch边界天然无缝; dValueA=128B/dValueB=2048B; 输出落点: L2驻留",67108864,0.0,4.194304e-05,0.0,4.234304e-05,8,4.0000000000000003e-07,34359738368.0,7.06990501399177e-05,67108864,1.290555076923077e-05,0.0,7.06990501399177e-05,2.1742932036720483e-05,9.244198217663819e-05,MMAD,True,,计算Bound,"瓶颈在 Cube 计算: 已接近理论算力上限, 检查是否有冗余计算 (MergeBatch 交叉项) 可消除"
b128_m4096_n4096_k8192,128,128,4096,4096,8192,bf16,bf16,bf16,False,False,False,True,0,b128_m4096_n4096_k8192,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,24,24,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,8192,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,2304,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=16384.0MB, V_out=4096.0MB, L2=128MB); 尾轮: r=0 无尾轮",17179869184,395136991232,0.01073741824,0.07598788292923077,0.08672530116923077,0.0,0.0,35184372088832.0,0.07239582734327572,4294967296,0.00268435456,0.0,0.08940965572923076,0.0,0.08940965572923076,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m8192_n4096_k7168,32,32,8192,4096,7168,bf16,bf16,bf16,False,False,False,True,0,b32_m8192_n4096_k7168,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,47,24,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,7168,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,1128,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=5376.0MB, V_out=2048.0MB, L2=128MB); 尾轮: r=0 无尾轮",5637144576,172872433664,0.00352321536,0.03324469878153846,0.03676791414153846,0.0,0.0,15393162788864.0,0.031673174462683126,2147483648,0.00134217728,0.0,0.03811009142153846,0.0,0.03811009142153846,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m2048_n2048_k8192,32,32,2048,2048,8192,bf16,bf16,bf16,False,False,False,True,0,b32_m2048_n2048_k8192,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,12,12,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,8192,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,144,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=2048.0MB, V_out=256.0MB, L2=128MB); 尾轮: r=0 无尾轮",2147483648,23622320128,0.00134217728,0.004542753870769231,0.005884931150769231,0.0,0.0,2199023255552.0,0.004524739208954733,268435456,0.00016777216,0.0,0.006052703310769231,0.0,0.006052703310769231,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b64_m4096_n2048_k128,64,64,4096,2048,128,bf16,bf16,bf16,False,False,False,True,0,b64_m4096_n2048_k128,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,24,12,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,128,128,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,576,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=96.0MB, V_out=1024.0MB, L2=128MB); 尾轮: r=0 无尾轮",100663296,1509949440,6.291456e-05,0.0002903748923076923,0.0003532894523076923,0.0,0.0,137438953472.0,0.0002827962005596708,1073741824,0.00067108864,0.0,0.0010243780923076921,0.0,0.0010243780923076921,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b16_m1024_n1024_k8192,16,16,1024,1024,8192,bf16,bf16,bf16,False,False,False,True,0,b16_m1024_n1024_k8192,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,6,6,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,8192,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,18,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=512.0MB, V_out=32.0MB, L2=128MB); 尾轮: r=0 无尾轮",536870912,2684354560,0.00033554432,0.0005162220307692308,0.0008517663507692308,0.0,0.0,274877906944.0,0.0005655924011193416,33554432,2.097152e-05,0.0,0.0008727378707692308,0.0,0.0008727378707692308,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b4_m32768_n128_k128,4,4,32768,128,128,bf16,bf16,bf16,False,False,False,True,0,b4_m32768_n128_k128,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,187,1,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,128,128,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"resident(整case全驻留S_A: 输出驻留L2异步回写, GM写=0)",4,0,方案B,205,1,1,205,1,12,24,True,2,"L2场景: A_整case全驻留(输入+输出<=L2) (V_in=32.1MB, V_out=32.0MB, L2=128MB); 尾轮: 面积型主导, A1b与方案B严格打平(T=28.96us), 选方案B工程简洁 (一套tile)",33685504,24379392,2.105344e-05,4.688344615384615e-06,2.5741784615384616e-05,0.0,0.0,4294967296.0,8.837381267489712e-06,33554432,6.452775384615385e-06,0.0,2.5741784615384616e-05,0.0,2.5741784615384616e-05,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b8_m32768_n2048_k512,8,8,32768,2048,512,bf16,bf16,bf16,False,False,False,True,0,b8_m32768_n2048_k512,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,187,12,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,512,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,561,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=272.0MB, V_out=1024.0MB, L2=128MB); 尾轮: r=0 无尾轮",285212672,6073352192,0.00017825792,0.0011679523446153847,0.0013462102646153848,0.0,0.0,549755813888.0,0.0011311848022386832,1073741824,0.00067108864,0.0,0.0020172989046153846,0.0,0.0020172989046153846,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b4_m131072_n128_k128,4,4,131072,128,128,bf16,bf16,bf16,False,False,False,True,0,b4_m131072_n128_k128,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,745,1,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,128,128,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,方案B,820,1,1,820,1,4,94,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=128.1MB, V_out=128.0MB, L2=128MB); 尾轮: 面积型主导, A1b与方案B严格打平(T=115.39us), 选方案B工程简洁 (一套tile)",134348800,97517568,8.3968e-05,1.875337846153846e-05,0.00010272137846153847,0.0,0.0,17179869184.0,3.534952506995885e-05,134217728,8.388608e-05,0.0,0.00018660745846153846,0.0,0.00018660745846153846,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b8_m131072_n1024_k256,8,8,131072,1024,256,bf16,bf16,bf16,False,False,False,True,0,b8_m131072_n1024_k256,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,745,6,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,256,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,方案B,820,7,1,820,7,16,1118,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=516.0MB, V_out=2048.0MB, L2=128MB); 尾轮: 面积型主导, A1b与方案B严格打平(T=1384.63us), 选方案B工程简洁 (一套tile)",541065216,5804916736,0.00033816576,0.0011163301415384615,0.0014544959015384616,0.0,0.0,549755813888.0,0.0011311848022386832,2147483648,0.00134217728,0.0,0.0027966731815384617,0.0,0.0027966731815384617,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b16_m32768_n8192_k7168,16,16,32768,8192,7168,bf16,bf16,bf16,False,False,False,True,0,b16_m32768_n8192_k7168,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,187,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,7168,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,方案B,205,52,1,205,52,16,4395,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=8960.0MB, V_out=8192.0MB, L2=128MB); 尾轮: 周长型主导, rho=0.50<rho_dv=0.53, A1b被dValue卡死, 方案B反超",9395240960,695247831040,0.0058720256,0.13370150596923078,0.13957353156923077,0.0,0.0,61572651155456.0,0.1266926978507325,8589934592,0.00536870912,0.0,0.14494224068923078,0.0,0.14494224068923078,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b4_m32768_n128_k8192,4,4,32768,128,8192,bf16,bf16,bf16,False,False,False,True,0,b4_m32768_n128_k8192,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,187,1,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,8192,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,方案B,205,1,1,205,1,12,24,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=2056.0MB, V_out=32.0MB, L2=128MB); 尾轮: 周长型主导, rho=0.38<rho_dv=0.53, A1b被dValue卡死, 方案B反超",2155872256,1560281088,0.00134742016,0.00030005405538461536,0.0016474742153846154,0.0,0.0,274877906944.0,0.0005655924011193416,33554432,2.097152e-05,0.0,0.0016684457353846154,0.0,0.0016684457353846154,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m131072_n8192_k128,32,32,131072,8192,128,bf16,bf16,bf16,False,False,False,True,0,b32_m131072_n8192_k128,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,745,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,128,128,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,35015,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=1088.0MB, V_out=65536.0MB, L2=128MB); 尾轮: r=0 无尾轮",1140850688,99321118720,0.00071303168,0.019100215138461538,0.019813246818461538,0.0,0.0,8796093022208.0,0.01809895683581893,68719476736,0.04294967296,0.0,0.06276291977846153,0.0,0.06276291977846153,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b64_m32768_n8192_k1536,64,64,32768,8192,1536,bf16,bf16,bf16,False,False,False,True,0,b64_m32768_n8192_k1536,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,187,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,1536,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,17578,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=7680.0MB, V_out=32768.0MB, L2=128MB); 尾轮: r=0 无尾轮",8053063680,595926712320,0.0050331648,0.11460129083076923,0.11963445563076923,0.0,0.0,52776558133248.0,0.10859374101491358,34359738368,0.02147483648,0.0,0.14110929211076922,0.0,0.14110929211076922,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b8_m131072_n8192_k8192,8,8,131072,8192,8192,bf16,bf16,bf16,False,False,False,True,0,b8_m131072_n8192_k8192,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,745,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,8192,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A1b,2,2,1,2,2,24,8754,True,2,"L2场景: C_双侧超L2: 最小替换2D分组(组间落空GM, 窗口L2) (V_in=17408.0MB, V_out=16384.0MB, L2=128MB); 最小替换分组 m_grp=22x n_grp=24 (GM倍率3.88, 窗口L2/batch=183168.0MB); 尾轮: 周长型主导, rho=0.75>=rho_dv=0.53, A1b恒优 (尾轮tile缩√rho=0.87倍凑满核)",70866960384,1536524550144,0.04429185024,0.2954854904123077,0.3397773406523077,0.0,0.0,140737488355328.0,0.2895833093731029,17179869184,0.01073741824,0.0,0.3505147588923077,0.0,0.3505147588923077,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b8_m16_n7168_k1536,8,8,16,7168,1536,bf16,bf16,bf16,False,False,False,True,0,b8_m16_n7168_k1536,StreamK,Ascend950PR,batch_mat_mul_v3,32,1,1,2,2,"B/M/N切出16块, 每块2核切K归约 (归约组内核c负责K段[c*K/2,(c+1)*K/2))",1,1,16,3584,768,256,1,K段标准分块流水,16,128,64,allocate(部分和驻留L2),"resident(部分和4B驻留L2, 防精度丢失不随C的fp16/fp8转换)",0,3670016,grid_K=2路切K+归约,1,1,2,0,0,0,0,True,4,"P=14.00, grid_K=2, 部分和驻留L2按4B写出, AIV归约后按C dtype=2B写最终",176553984,393216,0.00011034624,7.561846153846153e-08,0.00011042185846153846,0.0,0.0,2818572288.0,5.799531456790123e-06,0.0,0.0,2.566079254079254e-07,0.00011042185846153846,2.566079254079254e-07,0.00011067846638694638,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b64_m1024_n7168_k7168,64,64,1024,7168,7168,bf16,bf16,bf16,False,False,False,True,0,b64_m1024_n7168_k7168,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,6,41,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,7168,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,492,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=7168.0MB, V_out=896.0MB, L2=128MB); 尾轮: r=0 无尾轮",7516192768,70464307200,0.00469762048,0.013550828307692308,0.018248448787692308,0.0,0.0,6734508720128.0,0.013857013827423869,939524096,0.00058720256,0.0,0.018835651347692307,0.0,0.018835651347692307,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b32_m8192_n8192_k7168,32,32,8192,8192,7168,bf16,bf16,bf16,False,False,False,True,0,b32_m8192_n8192_k7168,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,47,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,7168,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,2209,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=7168.0MB, V_out=4096.0MB, L2=128MB); 尾轮: r=0 无尾轮",7516192768,345744867328,0.00469762048,0.06648939756307692,0.07118701804307692,0.0,0.0,30786325577728.0,0.06334634892536625,4294967296,0.00268435456,0.0,0.07387137260307693,0.0,0.07387137260307693,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b8_m4096_n4096_k128,8,8,4096,4096,128,bf16,bf16,bf16,False,False,False,True,0,b8_m4096_n4096_k128,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,24,24,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,128,128,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,144,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=16.0MB, V_out=256.0MB, L2=128MB); 尾轮: r=0 无尾轮",16777216,385875968,1.048576e-05,7.420691692307692e-05,8.469267692307693e-05,0.0,0.0,34359738368.0,7.06990501399177e-05,268435456,0.00016777216,0.0,0.0002524648369230769,0.0,0.0002524648369230769,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
b128_m8192_n8192_k7168,128,128,8192,8192,7168,bf16,bf16,bf16,False,False,False,True,0,b128_m8192_n8192_k7168,ASW_Basic,Ascend950PR,batch_mat_mul_v3,32,1,47,47,1,B->M->N线性映射+ASW滑窗蛇形(W=4),0,1,176,176,7168,256,1,双缓冲驻留当前tile输入,176,176,80,allocate(输入驻留L2吸收重复读),"direct_gm(输出直写GM, 输入优先驻留L2)",4,0,A0,1,1,1,0,0,0,8836,True,2,"L2场景: B_单batch可驻留(全驻留或单侧驻留+对侧滑窗) (V_in=28672.0MB, V_out=16384.0MB, L2=128MB); 尾轮: r=0 无尾轮",30064771072,1382979469312,0.01879048192,0.2659575902523077,0.2847480721723077,0.0,0.0,123145302310912.0,0.253385395701465,17179869184,0.01073741824,0.0,0.2954854904123077,0.0,0.2954854904123077,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"
special_k1_b64,64,64,8192,512,1,bf16,bf16,bf16,False,False,False,True,0,special_k1_b64,特殊分支,Ascend950PR,batch_mat_mul_v3,64,1,1,1,1,AIV 核间按行均分 (无 Cube tile 概念),0,1,0,0,1,0,1,UB驻留(AIV) AIV单缓冲,0,0,0,allocate,direct_gm,0,0,不涉及(AIV逐元素),1,1,1,0,0,0,0,False,2,"K=1逐元素乘: 退化为 C=A⊙B 无累加深度, Cube 16x16x16 粒度浪费 15/16; 走 AIV 通路 GM->UB->Mul->GM, AIV单缓冲 (B<2*AIV 逐batch单缓冲串行)",1114112,0.0,6.9632e-07,0.0,6.9632e-07,0.0,0.0,268435456.0,9.92969696969697e-06,536870912,0.00033554432,0.0,0.00033624063999999996,0.0,0.00033624063999999996,MTE2,True,,访存Bound(GM读写共享+L2重复读),"瓶颈在 MTE2 搬移链 (GM 读写共享总线 + L2 重复读): 可增大 tile 提升 dValue/单核搬移量、利用 L2 驻留吸收重复读 (ASW swizzle/分组方向), 或评估输出驻留 L2 以减少 GM 直写与读竞争"